I thought I’d just document how I made these little hats, then with the benefit of my experience you can venture forth and give it a go yourself, knowing I had no idea what I was doing but still managed to do it good enough regardless!
Things I used:
- Construction Paper (though any paper will do, this is just thicker so a bit easier)
- Spray Adhesive
- Fabric for hats (I used satin for the white one, and an acetate lining for the coloured ones)
- Scalpel / Utility Knife / whatever you want to call it
- Hot Glue and Hot Glue gun
- Box board/strawboard/thick cardboard, whatever you want to call it. As long as its a thicker board that is still (just) bendable and will keep its shape. I used a mixture of 1.2mm and 2.4mm thick card.
- Alligator Clips
- White Felt (though you could probably use some interfacing or something in lieu of this)
- Silkscreen kit– This obviously isn’t compulsory, its just how I did the patterning on the ribbon of the white hat.
First up, I made a basic pattern out of paper and tape to work from.
To do this, I started with the base of the hat. Using a compass, a pencil and some paper, I drew a large circle which would be the size of the brim that I wanted, and then an inner circle using the same center point to define the size of the crown or barrel of the rest of the hat. Then I cut it out, and made sure it was the right size by sticking it on my head and looking in a mirror!
Then to get the pattern for the shape of the crown/barrel that I wanted (which was slightly tapered), I wrapped up a bit of paper into a cone shape with the right tapering angle, taped it together, then put it through the center of the brim piece I had just cut out till there were no spaces between the hole in the brim and the cone (kinda like an upside down witches hat I guess… though there should be quite a bit above because that’s the hat part!!). Tracing along the part where the two bits of paper meet will now define the right size for base of the crown of the hat. Then I cut along this line, so that it would stand upright on the work surface. While it is standing, using a ruler, a steady hand and a sharpie, I kept the sharpie against the ruler at the right hat, and rotated the crown to mark out the top at the same height all the way around. Obviously you can use whatever method you want to do this, just make sure that the height is the same all the way around, or the pattern won’t be accurate!
Then cutting along the line just drawn, it will leave the shape of the crown/barrel of the hat! Then simply trace the circle for the top part of the hat. So you should have three pieces: the brim, the crown and the top.
Making the hat:
Using the pattern/template made from paper, trace out the pattern on card. I used the 2.4mm thick card for the brim and the hat, and the 1.2mm card for the crown. Cut out the pieces and place on a clean and disposable (ie covered with newspaper or something) work area. *note: before tracing out your pattern, make sure you’re tracing the crown part of the pattern in the right direction… some cards have a “grain” and its impossible to bend the card against the grain without ugly bends and creases
Iron the fabric to make sure there are no unwanted creases. Then spray both the cardboard and the fabric (sparingly on the fabric so that it doesn’t soak through and leave marks) with the spray adhesive. Wait till the glue is a bit tacky, and then carefully place the fabric over the pieces. Be careful there’s no hair or creases or anything, as it will show through. At this stage, it should look a bit like this:
However, if you want the brim curvy like the hats pictured, don’t glue the fabric to the brim at this stage, just the top and the crown. To curve the brim, soak it in water, then use a large round can or bottle to shape the card. The insides of the card will crease, but thats okay. When its dry, cover it with felt or interface (I used felt because that was on hand), and THEN glue the fabric on top.
Here’s what it looked like before I glued the fabric on (but after I glued the felt on):
Wait for the glue to fully dry before moving on. I generally put some heavy books on top and left it overnight to dry. Spray adhesive is generally pressure sensitive, so the more weight you put on it while it dries, the better it adheres.
When its dry, cut around the shapes.
Then using the spray adhesive again, on the backside spray the edges of the fabric and the cardboard. For the top circle piece, fold all the edges over when the glue has become tacky. Try to stretch the fabric as much as possible so you don’t see any folds around the edges.
For the crown piece (pictured above) just fold over the fabric on sides and the top. Leave the bottom side (the smaller side) alone for now, it will be easier to fold over when the crown has been shaped. Make sure the corner pieces are stuck down very well!
On the underside of the brim, use a sharp scalpel/knife to score and remove the fabric “folds” that have been created from folding the fabric over to the underside as well as the inner circle. Do this to eliminate all the bumps, as when it comes to covering this up every single bump and lump will show. The underside of the top circle will be hidden in the crown, so it is not necessary to clean the top circle unless you wanted to be neat.
Now comes the tricky bit — the assembly:
Slowly start bending the crown around the top circle. Use a flat surface, use one had to keep the top in place, and the other to bend the crown around. Be careful not to do it too quickly, as the card will break or bend and it will show under the fabric. This will look a bit funny and ruin the smooth finish, so if there’s ever a time to take it slow, this is it! When you have a quarter or so bent around, use the hot glue to glue the top and the crown together. That will make the continuation of bending a lot easier, as part of the crown will now be anchored to the top. Then continue gluing and bending until the crown and the top circle are as one. I needed to do some creative hot glue dropping and smearing to get the last bits stuck down. Then glue the sides of the brim together, and you should have the top part of the hat done!
Then its just a matter of gluing the completed crown to the brim, and then covering the bottom of the brim. You may want to use some interface or felt again to cover the bumps if you want to make it look professional. I didn’t, as while the hat is on you shouldn’t be able to see the bottom too much.
To cover the bottom of the brim, use the spray adhesive to glue together two bits of (the same) ironed fabric, and then glue it onto the brim when its dry. This way when you cut out the circle of the brim (I cut it out after I glued it on to make sure I got the right shape, not before), the fabric is much much much less likely to fray. I’ve been rubbing it a bit to test and there still isn’t any fraying, so it will last for as long as I need it to anyway.
Now you are ready for decorating:
A ribbon to cover the join between the brim and the crown would be my first suggestion, then something big and puffy to cover the join of the crown at the back (that way even if you made a mistake no one will even notice!).
Once you’re done with making it look pretty, turn it over and glue the alligator clips onto the bottom of the hat. I guess you could do this before you began decorating too. Whatever works for you.
And that’s the end of my long and confusing guide to making a mini top hat. I hope it gave you enough information to figure it out for yourself.